Anyone have issues with this lens using on Zeiss Ikon ZM camera? Rangefinder seems to be stuck. If I mount the lens while it is focused to infinity, then the rangefinder will work for few meters from the infinity and then it will get stuck. All other zeiss and voigtländer lenses I use work without any issues on my Zeiss Ikon body.
If you set the focus ring to 0.7m and then mount it on the camera, does it work correctly then?
I always ensure to mount and unmount my M lenses in my M cameras with the focus cam at its lowest setting, corresponding to minimum focus distance.
If you mount the lenses on the cameras while they are at infinity, you could damage the rangefinder mechanism in the camera or knock it out of calibration. It’s especially true for lenses who rotate a slopes cam when focusing, vs having a non rotating cam. The 7A uses the rotating cam slope type.
This happened to me, and had to send my M240 to Wetzlar to get fixed. It wasn’t a 7A lens that did this, but possibly a Nippon Kogaku lens I had from the 1950’s whom, when mounted on an LTM adapter, had its cam beyond the flush point of the mounting bayonet on the LTM adapter. I then placed force on the cameras swing arm, and not only did it sometimes knock my rangefinder it of calibration on the adjustable wheel, it broke something in the rangefinder eventually where the mirror prisms are.
The 7A lenses, because they have the ability to be adjusted by the user, also seem to have a cam slope that at its highest point, sticks deeper into the camera then the rear flange bayonet. Presumably to compensate for a stack up of tolerances wher in worst case, the highest slope of the cam is flush with the bayonet, but this means in others situation where the tolerances have stacked up the other way, can and do push the cam slope beyond the bayonet.
The rangefinder cam should roughly sit 0.1mm below the edge of the bayonet flange to correspond roughly to infinity. However, my 35mm and 28mm 7A have the top of the cam slope go beyond this. It becomes an issue if the cam was adjusted to have the highest point where it begins to flattens out meet the area where the cameras swing arm engages it.
If you mount the lens like this, while it is set to infinity, because the swing arm has a limiting tab that prevents focusing beyond infinity, you are using the lens to ram the swing arm into the camera and placing stress on the infinity limiting tab which is a component on the swing arm.
I don’t have a ZM Ikon, but I have a Cosina made Rollei 35RF and various Leica film and digital cameras, and while the swing arm designs are slightly different between them, the principle of how it works remains similar.
If adjusted properly, the cam slope on the lens should sit about 0.1mm below to flush with the bayonet edge at the rangefinder swing arm engagement point. But the part that is still higher to this will be right of the cam if you look at the lens from the rear.
It’s possible this part of the cam, which is higher then any Leica, Voigtlander or Zeiss cam is supposed to actually be, is getting caught or stressing the swing arm when you mount the lens at infinity focus setting.
Mounting the lens when set to 0.7m will ensure the high part of the cam slope is sufficiently out of the way of the rangefinder swing arm in the camera. Then, as long as the lenses cam slope never tried to go beyond infinity (0.1mm to flush with the rear bayonet) while it is engaged with the cameras rangefinder swing arm, you shouldn’t be placing stress on the infinity limiter and the rangefinder may stop jamming.
If you have just bought the lens, and are using it out of box, it’s possible it’s out of calibration and need calibrating. Easiest way to calibrate it is with a digital Leica camera if you can get access to one. One with live view like the M240 or M10 works even better and makes the process easier.
I’m not sure where you reside, but if you live in England, I could calibrate it for you on my Leica M240 with EVF. Shouldn’t take more then 30 minutes.
Cheers.
salasource1 wrote:
Anyone have issues with this lens using on Zeiss Ikon ZM camera? Rangefinder seems to be stuck. If I mount the lens while it is focused to infinity, then the rangefinder will work for few meters from the infinity and then it will get stuck. All other zeiss and voigtländer lenses I use work without any issues on my Zeiss Ikon body.
Sorry my bad, I meant to say 0.7 instead of infinity. So I did just that what you suggested.
Lens itself is calibrated correctly. When I use it on M10 it works just fine and focus is accurate (beside the bad de-center problem it also has https://i.imgur.com/ZOViH21.jpg).
WOW, this is some great information, thanks for sharing!
I have a Minolta CLE that I've just about resigned to using as a scale focus camera with wider lenses. Because the service manual is some sort of Holy Grail and nobody works on these anymore, I've gone the DIY route and - successfully - calibrated the rangefinder, only to have it slip out of whack a week later.
Definitely some things to consider here.
candreyo wrote:
If you set the focus ring to 0.7m and then mount it on the camera, does it work correctly then?
I always ensure to mount and unmount my M lenses in my M cameras with the focus cam at its lowest setting, corresponding to minimum focus distance.
If you mount the lenses on the cameras while they are at infinity, you could damage the rangefinder mechanism in the camera or knock it out of calibration. It’s especially true for lenses who rotate a slopes cam when focusing, vs having a non rotating cam. The 7A uses the rotating cam slope type.
This happened to me, and had to send my M240 to Wetzlar to get fixed. It wasn’t a 7A lens that did this, but possibly a Nippon Kogaku lens I had from the 1950’s whom, when mounted on an LTM adapter, had its cam beyond the flush point of the mounting bayonet on the LTM adapter. I then placed force on the cameras swing arm, and not only did it sometimes knock my rangefinder it of calibration on the adjustable wheel, it broke something in the rangefinder eventually where the mirror prisms are.
The 7A lenses, because they have the ability to be adjusted by the user, also seem to have a cam slope that at its highest point, sticks deeper into the camera then the rear flange bayonet. Presumably to compensate for a stack up of tolerances wher in worst case, the highest slope of the cam is flush with the bayonet, but this means in others situation where the tolerances have stacked up the other way, can and do push the cam slope beyond the bayonet.
The rangefinder cam should roughly sit 0.1mm below the edge of the bayonet flange to correspond roughly to infinity. However, my 35mm and 28mm 7A have the top of the cam slope go beyond this. It becomes an issue if the cam was adjusted to have the highest point where it begins to flattens out meet the area where the cameras swing arm engages it.
If you mount the lens like this, while it is set to infinity, because the swing arm has a limiting tab that prevents focusing beyond infinity, you are using the lens to ram the swing arm into the camera and placing stress on the infinity limiting tab which is a component on the swing arm.
I don’t have a ZM Ikon, but I have a Cosina made Rollei 35RF and various Leica film and digital cameras, and while the swing arm designs are slightly different between them, the principle of how it works remains similar.
If adjusted properly, the cam slope on the lens should sit about 0.1mm below to flush with the bayonet edge at the rangefinder swing arm engagement point. But the part that is still higher to this will be right of the cam if you look at the lens from the rear.
It’s possible this part of the cam, which is higher then any Leica, Voigtlander or Zeiss cam is supposed to actually be, is getting caught or stressing the swing arm when you mount the lens at infinity focus setting.
Mounting the lens when set to 0.7m will ensure the high part of the cam slope is sufficiently out of the way of the rangefinder swing arm in the camera. Then, as long as the lenses cam slope never tried to go beyond infinity (0.1mm to flush with the rear bayonet) while it is engaged with the cameras rangefinder swing arm, you shouldn’t be placing stress on the infinity limiter and the rangefinder may stop jamming.
If you have just bought the lens, and are using it out of box, it’s possible it’s out of calibration and need calibrating. Easiest way to calibrate it is with a digital Leica camera if you can get access to one. One with live view like the M240 or M10 works even better and makes the process easier.
I’m not sure where you reside, but if you live in England, I could calibrate it for you on my Leica M240 with EVF. Shouldn’t take more then 30 minutes.
Cheers.
...Show more →salasource1 wroteAnyone have issues with this lens using on Zeiss Ikon ZM camera? Rangefinder seems to be stuck. If I mount the lens while it is focused to infinity, then the rangefinder will work for few meters from the infinity and then it will get stuck. All other zeiss and voigtländer lenses I use work without any issues on my Zeiss Ikon body.
From the photos, it doesn’t look like the cam slope is beyond the bayonet whine at infinity, as I can see the slope continues to the right of where the swing arm engagement point would be.
It’s possible the lens is faulty though. I can’t see anything out of the ordinary with the lens that could fowl the Zeiss lion zm, but I also don’t have that camera.
If the lens works fine on the M10 as you say, then it’s possible there could be some compatibility issue between the two that has gone under the radar.
I know various different M mount cameras have different internal baffling, so some cameras like a Leica M5 don’t support certain collapsible lenses due to baffling that isn’t present on say a Leica M3 or M6. But the 7A 28mm has mainly its rear element poke into the camera, not a lot more like certain Leica Ultra wide angles have.
Considering the lens is also decentered, it’s worth while to try and return it if you can and exchange it for another copy.
A good copy of the lens is excellent performance to value, and I’m impressed how sharp the lens is across the frame once stopped down.
I own the non-fe plus version with ring flare, one of the first 100 made.
My copy is sharp across 90% of the in focus image plane stopping down just to f/2, and I can make the ring flare go away by setting the aperture to f/1.5’ish.
I know a lot of users here are using them on Sony cameras with good results, but the lens IMO really shines on a Leica, where the sensors microlenses can help yield a corner to corner sharp image by f/2.8-4. Impressive for a few hundred dollars! I think used 28mm Elmarit’s that still command a thousand dollar plus premium are going to feel the pressue slowly.
Since this lens easily outperforms most of the 28mm Rangefinder lenses that are pre-aspherical. I sold my Zeiss 28mm Biogon, 28mm Voigtlander Ultron and 28mm Elmarit ASPH, but have kept the 7a.
The 28mm Elmarit asph is sharper on my leica’s, but the corners are a mess on Sony without a pcx 1500 on the front.
It’s worth exchanging it for a good copy if you can to see if the Zeiss Ikon swing arm issue goes away.
salasource1 wrote:
Sorry my bad, I meant to say 0.7 instead of infinity. So I did just that what you suggested.
Lens itself is calibrated correctly. When I use it on M10 it works just fine and focus is accurate (beside the bad de-center problem it also has https://i.imgur.com/ZOViH21.jpg).
Does anyone else has these scratch marks on their 7artisans lens? I only tried this lens twice on Zeiss to see that it does not work, so most of these markings are probably made by Leica m10 rangefinder roller.
About returning the lens for replacement, there are no reasonable options to do so.
I bought mine from aliexpress seller (not the 7artisans official store) who was more interested in stalling than resolving the issue by asking me to make a video about lens de-center problem, which I did for him. After that he asked me to send "original" pictures even when original full sized jpeg files was already sent to him. And even after that he asked me to make new picture like this https://i.imgur.com/ocDTaGL.jpg because factory asked for them. So at that point it was clear that there is no way I'm going to send this lens back China on my own cost, even when they would offer this option, because the risk that I could be scammed was too high with this seller.