Hi folks,

I've been having problems with my Radiopopper JrX and Vagabond II. Apparently, the JrX set does not want to work with my strobe plugged into the Vagabond II. It causes the strobe to sputter and flicker constantly, and it will not trigger at all. I have this connected via the phone jack/cord. However, when I plug the strobe into mains, it works just fine.

When the JrX is connected via the flash sync, it works just fine (just like a PW), regardless of whether or not the strobe is connected to battery or mains.

Has anyone else had this problem? Does anyone know why this problem exists?

After a talk with some Radiopopper tech, it was advised to me that my Vagabond II may not be as "clean". Hmm..it works fine w/my strobe..

Anyone want to take a stab at what's going on?

-Jimmy

That blows. Good to know. Both manufacturers are going to blame the other, that's to be expected. Have you tried switching through different channels and putting some sort of ferrite/surge protector between the VB and your strobe?

Hey, we can't be responsible for what another vendor does. RP did this interface with no communication or authorization from Paul C. Buff.

I can acknowledge there are some interface anomalies with multiple classic Buff lights on an inverter. The necessary brown out can affect the RJ11 remote connection and cause oddities like this. These lights were designed long before the Vagabond was conceived. You can expect the same behavior with any other sine inverter.

Thank you for responding, Paul. I'll assume that the Alien Bee Max will not have these interface anomalies then?

Jimmy Ho wrote:
Thank you for responding, Paul. I'll assume that the Alien Bee Max will not have these interface anomalies then?
Correct. Unlike most digital monolights on the market, next generation Buff lights will operate down to 40VAC without problems. Typically, with multiple lights connected to an inverter like Vagabond or Innovatronics, the inverter output drops to 60 to 70VAC at the beginning of recycle, then rises to 120VAC. This crashes the uP in most digital lights and causes some problems with the telephone style remote jack circuits in classic Buff lights. Next generation Buff lights won't be affected.

But this brings up a potentially similar situation with Cyber Commander connected via telephone connector and CSR+ or CSRB+ and classic Buff lights - every thing mentioned can tolerate the "brown out" except for the analog remote input of the classic Buff lights.

The best interim workaround, until the next generation Buff lights appear, is to use a Honda generator instead of battery inverter, or to use manual control when using vagabond.

As for remote tripping of classic Buff lights with Vagabond, either the CSR or CSRB or CSR+/CSRB+ receivers connected to the 1/8" sync jack rather than the telephone style connector will avoid these problems - but the CC will not be able to do its magic - power control grouping, etc.

I hope this adds more clarification than confusion.

Jimmy Ho wrote:
Thank you for responding, Paul. I'll assume that the Alien Bee Max will not have these interface anomalies then?

But note that the ABMax no longer has the telephone jack analog port the RP uses. Some people seem to assume this but I asked a while back

Was your Vagabond at full charge or nearly depleted? Know anyone close by w/ a Vagabond that you can test with? That'd isolate the issue between the RP vs. your Vagabond.

The brownout condition sounds like something that might affect the CSR+ too...run the vagabond so it's low on power and then fire it while connected to the analog port and we'd find out...

Paul Buff wrote:
But this brings up a potentially similar situation with Cyber Commander connected via telephone connector and CSR+ or CSRB+ and classic Buff lights - every thing mentioned can tolerate the "brown out" except for the analog remote input of the classic Buff lights.


Paul, little confused here. So with my current AB400 and AB800 when used with vagabond II, I can expect similar problem when using CC to control power levels?

Paul Buff wrote:
But this brings up a potentially similar situation with Cyber Commander connected via telephone connector and CSR+ or CSRB+ and classic Buff lights - every thing mentioned can tolerate the "brown out" except for the analog remote input of the classic Buff lights.

The best interim workaround, until the next generation Buff lights appear, is to use a Honda generator instead of battery inverter, or to use manual control when using vagabond.


so how long will it be before i have CC full control using my Zeus when i am using the Vagabond II. i just aquired this setup figuring that it was fully compatible with the CC.
is nothing futureproof? do i have to wait for ZeusMax?

amplexis wrote:
is nothing futureproof? ...?


Then we would live in a world of no advancement. With advancement comes left overs. I wish the folks who make PW would have NOT attempted 'futureproofing' the Flex and Mini that some are having trouble with.

cordellwillis wrote:
amplexis wrote:
is nothing futureproof? ...?


Then we would live in a world of no advancement. With advancement comes left overs. I wish the folks who make PW would have NOT attempted 'futureproofing' the Flex and Mini that some are having trouble with.

i lived thru the complete collapse of innovation in the computer industry in the late 1990s when the big rule for being acquired or funded was "compatibility" with MSwindows. many great tools and interfaces died quickly when their creators accepted instant wealth. It is Paul's vision and will that make him a hero for me. I am very wary of "marketing" which is what many "professional" photographers make their living servicing which is probably why so many favor orthodox marketing.

"it's just that i read the AB online descriptions and Paul Buffs assurances that: The AC powered CSR+ and battery powered CSRB+ receivers interface between CYBER COMMANDER™ and every flash unit with a remote jack made by Paul C. Buff, Inc.™ since 1986.
Supported lights include AlienBees™, UltraZap, White Lightning Ultra, WLX Series and ZEUS™.
You can also use other manufacturer’s lights with CYBER COMMANDER™, but the function will be limited to remote tripping, grouping and the camera f-stop metering and display. Since they don’t contain a Buff-compatible remote jack the other features cannot be implemented."

i read this to mean that of course the CC would control recent products from Paul C Buff even when they were powered with a Paul C Buff Vagabond II

i guess i need to watch "Day at the Races" a few more times to understand this business.
http://www.youtube.com/watch?v=9LBIsDBC848&feature=PlayList&p=16566B493D8BED5B&playnext=1&playnext_from=PL&index=12

kenyee wrote:

But note that the ABMax no longer has the telephone jack analog port the RP uses. Some people seem to assume this but I asked a while back

Was your Vagabond at full charge or nearly depleted? Know anyone close by w/ a Vagabond that you can test with? That'd isolate the issue between the RP vs. your Vagabond.

The brownout condition sounds like something that might affect the CSR+ too...run the vagabond so it's low on power and then fire it while connected to the analog port and we'd find out...


The Vagabond was at full charge. I didn't realize the ABMax doesn't have the telephone jack anymore. That's very nice. CC all the way then.

I've gone ahead and returned my Radiopopper JrX set. It didn't work for my purposes, as I mainly wanted to control my strobes while on location. I'll wait for the Cyber Commander to be released.

-Jimmy

Jimmy: I'll hopefully be testing this on a shoot this Saturday and will post results. Did it sputter once the strobe was fired, or did it never work at all? Did you test w/ multiple JrX receivers? Just wondering how far you went debugging this to figure out what the problem was...

I also bought it to be used on location (and would do the same w/ the CC even though the controller seems a lot more useful for studio work)...certainly makes changing the power of a BD or umbrella much easier without having to fiddle w/ light stands.

p.s., I was a bit bummed when I found out the abmax didn't have the analog control port any more as well, but that's also probably why the cybersync controller for it is only $30 opposed to $80 for the cybersync+...

Well, what can I say? Cyber Commander brings incredible digital control and more to all PCB lights since 1986. Any other company come even close to that? All Buff lights ever made run from Vagabond - few current high end or low end lights with digital controls do. One relatively small bug with running analog interface remote control and Vagabond at the same time and I am an evil person again who doesn't care about customers and has no vision. My god people, you jump on me for not foreseeing every possible feature that might be present in 2009 back in 1986? Has any competitor done a better job of this than Paul C. Buff? I tell the truth, good and bad, and get jumped on for it every time.

As for the Zeus question, if you're going to use it with Vagabond, plug the CSR/CSRB into the 1/8" sync jack and control power at the pack - that the best you can do in 2009.

If you're interested in exactly what's going on with every new Buff product get the info here. I have put up this info on a temporary site to get the info out ASAP - it will be on our company websites very soon.

http://www.webecool.com

Paul Buff wrote:
As for the Zeus question, if you're going to use it with Vagabond, plug the CSR/CSRB into the 1/8" sync jack and control power at the pack - that the best you can do in 2009.

so if i want CC control in the field [and don't feel i can backpack a Honda generator] more than i want 2 stops i should send the Zeus back and wait for Einstein 640?
I certainly don't want to convey any sense that there is a loss of desire for a few Paul C Buff products in my life. let them be Einstein 640s.
it would be a good thing IMO to quickly update the CC product description to alert interested customers to this limitation. I assume that the CyberSync™ CST will trigger a Ranger if i get one for the times i need more light.
Live long and do great work Paul, i am grateful you are doing what you do.

Paul Buff wrote:
One relatively small bug with running analog interface remote control and Vagabond at the same time and I am an evil person again who doesn't care about customers and has no vision.

Paul: no one said you were evil.
It's probably too early to ask, but why does low voltage on the analog control port freak out a cybersync+? I'm curious if it's possible to work around it in an updated cybersync+?

Sounds like the RP folks didn't test this either (you'd think it's a common enough configuration that they would have included it in their test matrix), but I'll confirm this weekend...

kenyee wrote:
Paul Buff wrote:
One relatively small bug with running analog interface remote control and Vagabond at the same time and I am an evil person again who doesn't care about customers and has no vision.

Paul: no one said you were evil.
It's probably too early to ask, but why does low voltage on the analog control port freak out a cybersync+? I'm curious if it's possible to work around it in an updated cybersync+?

Sounds like the RP folks didn't test this either (you'd think it's a common enough configuration that they would have included it in their test matrix), but I'll confirm this weekend...


This problem is not in the Cyber Sync - it is in the lights themselves. It's always been there and the same idiosyncrasies show up when using LG4X, RRI or RC1 remotes - it has existed for ever since Vagabond was introduced 8-9 years ago. Technically, the differential op amps that form the analog remote input latch up when the remote is connected via the telephone jack and the AC power drops below a critical voltage. There are just not enough people using Vagabonds and remote power control at the same time for it to have ever become a real big issue.

The only fix would be for us to recall 1/2 million lights and do some sort of retrofit.

And, Oh, the you tube link comparison sort of implies that I am a slippery salesman that cheats people - that where the "evil" statement originates.

amplexis wrote:
Paul Buff wrote:
As for the Zeus question, if you're going to use it with Vagabond, plug the CSR/CSRB into the 1/8" sync jack and control power at the pack - that the best you can do in 2009.

so if i want CC control in the field [and don't feel i can backpack a Honda generator] more than i want 2 stops i should send the Zeus back and wait for Einstein 640?
I certainly don't want to convey any sense that there is a loss of desire for a few Paul C Buff products in my life. let them be Einstein 640s.
it would be a good thing IMO to quickly update the CC product description to alert interested customers to this limitation. I assume that the CyberSync™ CST will trigger a Ranger if i get one for the times i need more light.
Live long and do great work Paul, i am grateful you are doing what you do.

Yes, you can return the Zeus if you feel you were misled. I can't update the CyberSync or it's instructions since the problem is not in the CyberSync. Can you adjust the power of the Ranger wirelessly? If not, you are not gaining anything. Are you in a shooting situation where you can't manually adjust the Zeus power and use the 1/8" sync jack to trigger it? You can fire the Ranger from CyberSync but you can't control its power via Cyber Commander.

Yes, the Einstein will do all you want, but is not 2500WS. Is the Ranger?

Paul Buff wrote:
Yes, you can return the Zeus if you feel you were misled. I can't update the CyberSync or it's instructions since the problem is not in the CyberSync. Can you adjust the power of the Ranger wirelessly? If not, you are not gaining anything. Are you in a shooting situation where you can't manually adjust the Zeus power and use the 1/8" sync jack to trigger it? You can fire the Ranger from CyberSync but you can't control its power via Cyber Commander.
Yes, the Einstein will do all you want, but is not 2500WS. Is the Ranger?

so it seems that the Zeus is as limited as the Ranger in the amount of control i have when away from AC. but the Ranger is substantially lighter as a battery powered light than the Zeus powered by a Vagabond II. 14.3 lb for the ranger RX vs 25 lb for Zeus 1200 pack and Vagabond II. in my mind it is worth the pain of carrying the extra weight if i can put the Zeus on a ledge across the creek and control it's power from where i sit.
i live in a 400 sq ft cabin and have no use for any light that needs AC. all my work is out in the bush. am i missing something about where i get more remote control with CC using the Zeus than with a third party light?
everything else you are offering Paul, is a very exciting and welcome achievement.

Paul Buff wrote:
Well, what can I say? Cyber Commander brings incredible digital control and more to all PCB lights since 1986.

If it ever comes out of vapourware, like the max's...

Jimmy Ho wrote:
I've gone ahead and returned my Radiopopper JrX set. It didn't work for my purposes, as I mainly wanted to control my strobes while on location. I'll wait for the Cyber Commander to be released.

-Jimmy

Jimmy, but you would have same problem with CC (when controlling power using vagabond II) unless you upgrade to the newer digital interface lights from AB, isn't it?