douglasf13 wrote:
I just received my NEX-7 a couple of hours ago...
- The camera is nearly identical in size as my 5N with the Ciesta leather half grip attached, so they feel very similar in the hand (without the 5N EVF attached, of course.) I almost want to say I prefer the 5N\'s grip slightly, since the leather of my half grip is worn in to fit my hand, but it\'s probably just because the 7 is new to me. The grip of the 7 is nice and rubbery, and I could always get a leather case for the 7, too.
- The extra dials and customizability of the 7 seem very handy, and once I get the hang of the new interface, I think it\'ll be a worthy step up.
I look forward to your comparison of 7 vs 5N operation. Without benefit of 5N use, I am trying to develop operational efficiencies with the NEX7. I think a common button mapping for MF lenses is MF assist to the AF/MF button. Then, instead of using the L and R wheel for moving the magnified target rectangle, I use the 4 directions of the control wheel. I wish there was a position reset method for homing the magnified target rectangle back to center frame.
I also noticed that optimal right hand position, for controling the upper buttons and wheels is up in the hand so only the middle finger really grasps the hand grip. The lower 4th and 5th fingers don\'t really provide any hold or support, for me. I have designed a NEX7 handgrip that adds 1/2 inch height to the camera and gives a grip that allows the 4th finger to grasp the grip and underside of the camera for increased hold and better positioning of the hand to control the operation of the camera. For example, the first joint of the thumb is placed over the control wheel and controls the 4 direction/softkey C array, while the thumb tip is in position over the AF/MF button.
The grip is of aluminum and provides space to open the battery door without unscrewing the grip from the tripod socket. It includes a Arca Swiss compatible dovetail and threaded 1/4-20 hole. It also provides clearance for the rear LCD screen to tilt down at full tilt, and a robust tripod mount whether using a quick release clamp or tripod threaded stud, relieving the stress of the thin bottom build of the camera. I will post a photo, hopefully next week.
douglasf13 wrote:
I just received my NEX-7 a couple of hours ago...
- The camera is nearly identical in size as my 5N with the Ciesta leather half grip attached, so they feel very similar in the hand (without the 5N EVF attached, of course.) I almost want to say I prefer the 5N\'s grip slightly, since the leather of my half grip is worn in to fit my hand, but it\'s probably just because the 7 is new to me. The grip of the 7 is nice and rubbery, and I could always get a leather case for the 7, too.
- The extra dials and customizability of the 7 seem very handy, and once I get the hang of the new interface, I think it\'ll be a worthy step up.
I look forward to your comparison of 7 vs 5N operation. Without benefit of 5N use, I am trying to develop operational efficiencies with the NEX7. I think a common button mapping for MF lenses is MF assist to the AF/MF button. Then, instead of using the L and R wheel for moving the magnified target rectangle, I use the 4 directions of the control wheel. I wish there was a position reset method for homing the magnified target rectangle back to center frame.
I also noticed that optimal right hand position, for controling the upper buttons and wheels is up in the hand so only the middle finger really grasps the hand grip. The lower 4th and 5th fingers don\'t really provide any hold or support, for me. I have designed a NEX7 handgrip that adds 1/2 inch height to the camera and gives a grip that allows the 4th finger to grasp the grip and underside of the camera for increased hold and better positioning of the hand to control the operation of the camera. For example, the first joint of the thumb is placed over the control wheel and controls the 4 direction/softkey C array.
The grip is of aluminum and provides space to open the battery door without unscrewing the grip from the tripod socket. It includes a Arca Swiss compatible dovetail and threaded 1/4-20 hole. It also provides clearance for the rear LCD screen to tilt down at full tilt, and a robust tripod mount whether using a quick release clamp or tripod threaded stud, relieving the stress of the thin bottom build of the camera. I will post a photo, hopefully next week.
